Bend Shop Plasma table

Active S-73000-00018406 RFQOffice Supplies & EquipmentDepartment of Transportation
The full text, documents and contacts of this bid come with a ProposalWorkspace plan.Get started

At a glance

Department of Transportation (Oregon) posted this RFQ on Nov 18, 2026. Responses are due Dec 2, 2026. Category: Office Supplies & Equipment. Solicitation number S-73000-00018406.

Solicitation details

General information

Solicitation number
S-73000-00018406
Notice type
RFQ
Place of performance
Oregon

Agency and category

Agency
Department of Transportation
Category
015Office Supplies & Equipment
Source listing
Link with a plan

Description

From the agency listing

The purpose of this RFCQ is to establish a Contract for the purchase of a plasma table for the benefit of ODOT.

Summary

AI-read from the bid documents

Summary fields on this page were extracted by AI from the bid documents. Always verify dates, amounts and requirements against the official solicitation.

What the bid is for

The Oregon Department of Transportation’s Central Oregon Fleet Repair Shop in Bend (Bend Shop) seeks to replace its existing plasma cutting table and system.

The purpose of this RFCQ is to establish a Contract for the purchase of a plasma table for the benefit of ODOT. The work contemplated under the Contract includes all labor, materials, transportation, equipment and services for, and incidental to, the completion of all Work in connection with the project described in the Contract Documents.

Scope

The Bend Shop supports heavy equipment repair and requires a cutting system suitable for industry level repairs and fabrication work. A 6’x12’ cutting area is needed to accommodate industrial level work products without the additional cutting, repositioning, or joining that a smaller table would require. The equipment will be used to cut materials sized 6’ x 12’ up to 2”. The equipment must also fit within the existing shop space while allowing necessary access and operating clearances.

Awarded contractor must deliver, unload and set up the plasma table. There is a forklift onsite for unloading and placement of the equipment. Voltages available in the room where the equipment will be installed are 220V, 3 Phase.

The awarded contractor must have a support and repair location located within 150 miles of the Bend Shop located at 63055 N Hwy 97 Bldg. G Bend, OR 97703 and have a 24-hour on-site repair response time.

The new plasma cutting table and system must be compatible to the current software that integrates CAD (computer aided design), CAM (computer aided manufacturing), and CNC (computer numerical control) and without additional licenses or subscriptions to run the existing software.

**Required** features include:

  • 6'x12' CNC Plasma Table with high definition capable
  • Cutting Envelope: 147”L x 73”W x 6.75" H
  • Overall Dimensions: 200”L x 124”W x 60”H
  • 8 inch deep water table with air ballast system or approved equal
  • Fully welded construction — not bolted or assembled from modular sections
  • Plasma Hypertherm maxpro200 220 volt – 3 phase plasma system or approved equal
  • Laser Plate Alignment System
  • Freestanding mobile control console with 15' wire harness for Flashcut control systems
  • Control Pendant w/ X, Y, Z Joystick
  • Logic Board Digitizing System
  • Setup, installation, and test table and associated attachments for full operations

**Operator/Maintenance Orientation Training:** Contractor shall provide pricing for the services of an experienced trainer for a maximum of **16 hours** of training to cover all features and options of the equipment provided. Training will be held at: Bend Maintenance Facility, 63055 N. Hwy 97, Bldg. B, Bend, OR 97703.

**Warranty:** The basic comprehensive warranty on the plasma unit must be for 6 years. The basic warranty on the motion control items must be for a minimum of 3 years. The basic warranty on the computer, mouse and keyboard must be for a minimum of 2 years. Contractor shall be responsible for responding to all necessary Warranty Repairs within 48 hours of notice from ODOT.

Additional information

Quotes must be submitted through the OregonBuys system.

Delivery is required within **90 calendar days** of receipt of notice to proceed. Delivery Location: 63055 N Hwy 97, Bldg G, Bend OR 97703

Owner may initiate, at any time, withholding of payment equal to 5% of the amount of each invoice submitted. Payment to Contractor for Goods and Services provided will normally be made within 30 calendar days following the date the invoice is received.

**Insurance** (Contractor shall obtain the insurance specified below prior to the execution of the Contract):

  • Commercial General Liability: **$1,000,000** per occurrence and **$2,000,000** annual aggregate
  • Commercial Automobile Liability: **$1,000,000** combined single limit per occurrence
  • Workers' Compensation and Employer’s Liability: not less than **$500,000** for each accident

Documents

2 files

Subscribe to get these 2 documents.

Similar open bids

In Oregon

More from Department of Transportation

Open bids