Acoustic Doppler Velocity Sensor Repair Services

Active DFW22183 RFQEnvironmental ServicesDallas Fort Worth International Airport
The full text, documents and contacts of this bid come with a ProposalWorkspace plan.Get started

At a glance

Dallas Fort Worth International Airport (Texas) posted this RFQ on Nov 17, 2026. Responses are due Nov 20, 2026. Category: Environmental Services. Solicitation number DFW22183.

Solicitation details

General information

Solicitation number
DFW22183
Notice type
RFQ
Place of performance
Texas

Agency and category

Agency
Dallas Fort Worth International Airport
Category
008Environmental Services
Source listing
Link with a plan

About this listing

ProposalWorkspace summary

This bid was found on the agency's procurement portal. The portal's own text is not republished here; the summary below was written by ProposalWorkspace's AI from the bid documents. The full posting is on the portal - subscribe to get the link.

Summary

AI-read from the bid documents

Summary fields on this page were extracted by AI from the bid documents. Always verify dates, amounts and requirements against the official solicitation.

What the bid is for

The Dallas-Fort Worth International Airport Board (Airport Board) intends to procure Acoustic Doppler Velocity Sensor Repair Services as described within the attached Specifications.

The Dallas/Fort Worth International Airport Board (Board) is seeking quotes for Acoustic Doppler Velocity Sensor Repair Services as specified herein.

Pricing shall include delivery F.O.B. DFW International Airport, 3122 East 30th Street (Central Warehouse), DFW Airport, Texas 75261. The Airport Board is tax exempt.

Scope

Acoustic Doppler Velocity Sensor Removal, Installation, and Calibration (Confined-Space, Underground Location)

This Scope of Work defines the responsibilities, tasks, and deliverables associated with the removal of an existing failed 1 MHz Acoustic Doppler velocity sensor and the installation, configuration, and calibration of a new replacement sensor within an underground confined-space wastewater channel. The objective is to restore accurate and reliable flow measurement consistent with manufacturer specifications and site operational requirements.

Work will be performed in an underground wastewater structure classified as a permit-required confined space. Atmospheric hazards, limited access, and wastewater exposure must be considered at all times. All work shall adhere to relevant OSHA regulations and the Owner's confined-space entry policies.

Contractor Responsibilities

  • Review existing system drawings, wiring diagrams, and installation records.
  • Verify site entry requirements, access points, and LOTO procedures.
  • Conduct a pre-job safety meeting covering confined-space risks and rescue procedures.
  • Confirm compatibility of the new sensor with the existing transmitter, cabling, and SCADA system.
  • Perform lockout/tagout of electrical circuits or flow controls affecting the work area.
  • Disconnect electrical and signal wiring from the existing sensor.
  • Remove the failed sensor and any associated mounting hardware as needed.
  • Install the new 1 MHz Acoustic Doppler velocity sensor using approved mounting hardware.
  • Route and secure cabling to prevent strain, submersion, or abrasion.
  • Configure all sensor parameters, including velocity range, sample rate, profiling settings, and channel geometry.
  • Validate communication with SCADA or the data acquisition system.
  • Perform manufacturer-recommended calibration and initialization procedures.

Upon completion, the contractor shall provide a commissioning package including as-found and as-left conditions, atmospheric monitoring logs, a completed confined-space entry permit, sensor configuration parameters and calibration records, photographs of the installation, and verification of SCADA point mapping and signal integrity.

Deliverables

  • Fully installed, operational, and calibrated Acoustic Doppler velocity sensor.
  • Complete documentation package and commissioning report.
  • Verification of accurate SCADA reporting and proper integration with existing control systems.

Additional information

All communication regarding this opportunity, including quotes must be submitted through https://dfwairport.bonfirehub.com and WILL Not be accepted via mail or email.

The Board intends to award a purchase order(s) to the lowest, responsive, responsible bidder(s). The Board reserves the right to split the award and issue multiple purchase orders that is in the Boards best interest.

Any quantity stated herein is an estimated quantity. The Airport Board reserves the right to purchase more or less than the estimated quantity of any or all the services listed in the Request for Quote as it deems to be in its best interest.

*Purchase Order Terms and Conditions* (attached) shall apply to any Purchase Order placed as a result of this Request for Quote.

Quotes shall be valid for 60 days.

Delivery must be accomplished during the hours of 8:00 A.M. and 4:00 P.M., Monday through Friday (excluding Airport Board-observed holidays). All prices quoted will be F.O.B. destination, freight prepaid and allowed.

The services offered shall be fully warranted against defects in material and workmanship for the full period customarily extended to governmental organizations. Full warranty statement must accompany quote.

Documents

2 files

Subscribe to get these 2 documents.

  • PO Terms and Conditions.docx
    Download
  • RFQ22183 Acoustic Doppler Velocity Sensor Repair Services.pdf
    Download

Similar open bids

In Texas

More from Dallas Fort Worth International Airport

Open bids